Warrior Generic LED Corner (Universal) Manuel d'utilisateur télécharger pdf

Protecting Your Adventure Lifestyle

========================================================================================

QUALITY • INTEGRITY • INNOVATION • SERVICE

Warrior Products, Inc.

16850 SW Upper Boones Ferry Rd

Ste. A

Durham, OR 97224

Phone (888) 220-6861

Fax (503) 692-0364

[email protected]

Generic LED Corner

Installation Instructions

All corners are designed to be placed over the existing factory metal body. During shipping and handling your aluminum

corners may be slightly altered but diamond plate aluminum is easy to tweak and bend back into form. Make any slight

modifications needed to enhance their fit. Also, because all body tubs are not built the same, some small modifications to

the Corners may be required for a proper fit.

Rivets are supplied for mounting your corners to the body tub. If you prefer you can use self tapping bolts. Installation

does not require the use of any sealant, but you may silicone seal your corners to the body if you prefer. You may want to

spray any exposed metal with primer before installing your Corners.

Corners are designed for use with our part #2917 LED Tail Light & Reverse Light Kit, which includes standard grommet

mounted 4” Tail Lights and 2” Reverse Lights.

Installation:

1. Remove all tail lights, side markers, the gas tank rubber filler housing, and any other item that may be in the way

of your installation process. 97 and newer models do not need to have the gas tank filler plastic removed at all, as

the corner will fit over the plastic.

2. Hold your Corners in place and mark the two round holes for your LED Tail Light Cutouts.

3. Once the holes are marked on your Jeep, set the corners aside and cut out the holes. When cutting these, you

can start the process by drilling starter holes and then use a metal bladed saw to make the cuts. It is

recommended to cut the hole slightly larger (approximately 1/8” greater diameter) than the hole in the LED Corner

for better grommet fitment.

4. Once the holes are cut, you may want to use a die grinder with a carbide bit or stone to smooth the edge. Finish

by painting the exposed metal with primer. On the 07 and later JK Wrangler model, you will also need to drill a

hole on the passenger side so that the reverse light grommet can get from the tail light area over to the reverse

light area, as there is a single layer body panel that blocks access.

5. You can now begin installing the corners. You will need a 3/16” drill bit and drill, as well as a pop-rivet tool.

6. Once you’ve got all of your rivets securely attached and the corners are on the vehicle securely, you can re-

assemble any parts removed in step #1 that need to go back into place.

7. Note: On some TJ models you will find a fuel canister that interferes with installing the passenger tail light. You

will need to relocate this box slightly in order to install the tail light. The simplest relocation is to loosen it and just

slightly move it forward. You should be able to get most of the bolts reinstalled with this method.

8. The last part of the installation is to install your tail lights. If you’ve chosen to use our light kit, begin by wiring our

taillight and reverse light pigtails into your factory wiring on the vehicle. Wire to wire will vary on the vehicle, so

some testing will need to be done to identify which wires you will be using. Our light grommets simply press into

place in the holes you’ve cut. The LED light kits will include a wiring help document that you can reference for

assistance.

9. Once the wiring is complete and the grommets are in place, plug your lights into the pigtails and then test to make

sure they are working. The reverse lights pigtail can be reversed, so if it is not working, try spinning the plug

before attempting to backtrack any other wiring errors.

10. With the taillights and reverse lights working, pop them into place by pushing them evenly into the grommets.

This will complete your installation.

Thanks for purchasing Warrior Products!

Résumé du contenu

Page 1 - Installation Instructions

Protecting Your Adventure Lifestyle========================================================================================QUALITY •

Commentaires sur ces manuels

Pas de commentaire

Warrior Generic LED Corner (Universal) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Warrior Generic LED Corner (Universal). Warrior Generic LED Corner (Universal) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Warrior Generic LED Corner (Universal)